TONY Briquetting Machine is a kind of curing molding equipment that compreses coarse fibers such as sawdust or crop straw and forest harvesting residues into lumping fuel through the process of dust removal, compression and shaping. The compressed fuel is blocky, small in size, dense and without any additives. It is easy to store and transport, the combustion value per unit area is increased by ten times, and the heat production and smelting resistance are close to that of medium coal. TONY Briquetting Machine adopts spiral prepressing, piston stamping, two-stage compression process, forced cooling of oil to ensure equipment lubrication, which solves the shortage of high water content of raw materials and fast wear of forming mold of ordinary block press; The equipment has the characteristics of low power consumption, high production efficiency, long mechanical operation life and low maintenance rate. Biomass fuel can replace coal, oil and other conventional energy, widely used in industrial production, government agencies, enterprises and institutions, urban residents heating, residents cooking, high-grade fireplaces and tobacco farmers flue-cured tobacco, can also be used as a biomass power plant power generation raw materials.

TONY Briquetting Machine Principle Mainly Includes The Following Steps:

Material Preparation:

The wood chips or other biomass materials are initially treated, such as crushing and crushing, so that they reach the appropriate particle size and water content. Generally, the length of the material should be controlled below 50mm, and the moisture content should be between 10% and 20%.

Charge:

The treated material is fed into the feed port of the press through the feeding conveyor. The feeding conveyor is usually equipped with an iron removal device to prevent metal impurities from entering the machine and damaging the equipment.

Compression Molding:

After the material enters the press, the motor drives the reducer, and then the reducer drives the spindle to rotate, and the spindle drives the press roller to rotate. The pressure between the roll and the die causes the material to be forced out of the model hole in bulk.

The radial clearance between the press roll and the die can be adjusted to ensure that the material will not be squeezed or bored during the compression process, ensuring the stability of the discharge.

Heating Assistance:

Some advanced block presses are equipped with an up and down electric heating ring, which can heat the mold and help the forming of the material, especially in the case of high water content.

Discharge:

The compressed wood chips fall from the discharge port, are cooled (moisture content does not exceed 14%), and are packed in bags.

TONY Briquetting Machine uses agricultural and forestry wastes such as corn stalks, wheat straw, cotton stalks, rice straw, rice husks, peanut shells, corn cobs, branches, leaves, sawdust, animal manure, etc. as raw materials and crushes them into biomass briquette fuel, commonly known as ' Straw coal's machinery and equipment. Briquette Machine is used in compression and densification molding in biomass fuel plants, feed mills, power plants, lumber mills, furniture factories, fertilizer plants, chemical plants, etc. 1. The finished material forming stable 2. Mould long life. 3. Jigh Capacity, high density 4. Simple operation 5. Wide applicability of different raw materials

1. The raw materials of TONY Briquetting Machine are widely applicable, suitable for all kinds of crop straw, rice husk, peanut shell, grass and so on.

2. TONY Briquetting Machine is equipped with electric heating system and temperature control system.

3. Unique double motor double pressure wheel technology.

4. The mould of TONY Briquetting Machine is treated by special process, and the service life is longer.

5. The equipment runs stably and the machine has a long service life.

6. Pressed out of the finished product, less ash, high flammability.

7. TONY Briquetting Machine are made of high quality materials, thick and solid.

8. The application range of TONY Briquetting Machine is very wide, which can press feed and fuel.

9. TONY Briquetting Machine is a cost-effective equipment, can be used as a small cost of self-use or investment equipment.

10. TONY Briquetting Machine is mainly composed of feed belt conveyor, feed port, motor and discharge belt conveyor.

TONY Briquetting Machine has a variety of models, according to the customer production of different models, Briquetting Machine factory price is not the same. You get what you pay for. The price always depends on the value. Because the pellet machine market is currently more chaotic, customers must be careful to buy! To make a purchase decision after a comprehensive inspection of a number of comprehensive indicators such as product quality, manufacturer scale strength, pre-sales and after-sales service ability, research and development design ability, rather than just looking at the price! Please note: If your purchase cost is very low, the later use cost will be very high! Because the purchase of very low cost equipment is likely to cause you to face endless maintenance later, continuous downtime and maintenance will delay your production and make you pay more money.

Development prospects of biomass fuel compaction:

Biomass energy is the fourth largest energy after coal, oil and natural gas, is a clean fuel that meets environmental protection requirements and can replace coal, and is a key development direction in the future. Biomass fuel is widely distributed, many kinds, inexhaustible, can be recycled clean new energy, with biomass instead of traditional coal burning, it not only solves the problem of energy shortage, but also solves the problem of environmental pollution, is an effective way to achieve China's emission reduction targets.

1. Outstanding Environmental Protection And Cleanliness.

The production process of biomass pellet fuel products adopts clean processing technology without "three wastes". It does not contain harmful substances, and the gas emitted after combustion is clean and harmless, which is conducive to improving the urban environment.

2. Low Cost, Easy To Buy Raw Materials

Compared with coal, natural gas and liquefied gas, biomass compaction fuel has low cost, easy purchase of raw materials, wide sources, waste reuse, income generation for farmers, and is in line with sustainable development strategy.

3. Biomass Compaction Is More Convenient To Use

The biomass block is easy to use, and the boiler does not need to be changed, only the dust removal can be changed.

4. Biomass Compaction Has A Wide Range Of Application

Biomass compaction can be widely adapted to a variety of fuel equipment. Such as: biomass boiler, coal-fired boiler, hot blast stove, heat conduction oil furnace equipment.

5. Production Is Not limited By Season And Scale

Biomass compaction can be produced all year round. The scale of production can be determined according to the economic situation of the unit or individual, the market and other factors, and can be large or smal

TONY Briquetting Machine uses agricultural and forestry wastes such as corn stalks, wheat straw, cotton stalks, rice straw, rice husks, peanut shells, corn cobs, branches, leaves, sawdust, animal manure, etc. as raw materials and crushes them into biomass briquette fuel, commonly known as ' Straw coal's machinery and equipment. Briquette Machine is used in compression and densification molding in biomass fuel plants, feed mills, power plants, lumber mills, furniture factories, fertilizer plants, chemical plants, etc.

Three main uses of TONY Briquette Machine:

1. Due to the high combustion rate of the block and easy storage, it can be used for domestic heating and living energy;

2. At the same time, the pressing block can also replace coal as the main fuel of industrial boilers, which reduces the cost and environmental health;

3. Can also be used as a fuel for power generation, with biomass fuel power generation, efficient and environmentally friendly.

History: TONY has more than ten years of professional experience in crusher development, design, export and installation.	R&D: TONY has a design team of 30 engineers, which can customize crushing equipment according to customers' specific requirements.	Hardware: TONY has the world's leading machining and numerical control center, to ensure the quality and quantity of the machine.	Inspection: TONY has a professional quality inspection team responsible for pre-delivery inspection to ensure product quality.
Standard: All TONY machines are in line with national standards, German standards, American standards, and CE certification.	Quality of spare parts: All spare parts of TONY are made of heavy machinery anti-fatigue and wear-resistant materials to extend the service life.	Installation: TONY has more than 30 professional installers and engineers, with more than 15 years of installation and commissioning experience,can provide overseas mechanical services.	After-sales service: TONY has 24 hours online service, contact us, you will get a professional reply